![]() ![]() ![]() In effect, I can mount the two folders on the host using file sharing if I log in as “guest” from the guest OS I cannot log into the host with my host admin user name/pw. However, this does not work as expected, only partially. (Configure your host OS to show all extensions so you can find the "vbox.log", not "vbox.log.1", Sharing permissions in the host are set to give read & write access to two specific folders to my host’s administrative user. In the "Logs" subfolder, zip the VM's "vbox.log", and post the zip file, using the forum's Upload Attachment tab. Right-click the VM in the main Virtualbox window's VM list, choose Show in Explorer/Finder/File Manager. If not possible, close the Virtualbox window for the VM with the Power Off option set. Run until you see the problem happen, then shut down the VM from within the VM's OS if possible. Start the VM from full normal shutdown, not save-state. In each OS provide the output of the " ifconfig" command. (Configure your host OS to show all extensions if the folder that opens does not show a. vbox-prev file), and post the zip file, using the forum's Upload Attachment tab. If you need further help, please post the following: Set up the VM OS to look to 192.168.56.1 for file sharing, and the host to look to 192.168.56.# (where # is the last number in the VM's IP address). Host-Only will default to giving the VM a 192.168.56.# IP address, and the host will have a 192.168.56.1 IP address. (Don't keep Bridged up if you have to go to this workaround.) NAT will put internet in the VM, you should be able to ping 8.8.8.8. If you cannot get Bridged to get IP address and ping, then you have to use NAT & Host-Only. Once this is established, set the Mac OS file and screen sharing settings to get file sharing, as you now have a full network between the host and the VM. If each ping goes through, you have full network access. Then ping the host's IP address from the VM, and the VM's IP address from the host. Open the host and VM OS's firewalls to allow ping in each OS. If it does, and you can then ping 8.8.8.8 (Google DNS) then you have internet in the VM. See if the VM gets an IP address in the host LAN's range from the house router. ![]() Still wondering why screen sharing would work but file sharing not.Īlbaraka wrote:leaving NAT on for Adapter 1, and enabling both bridged for Adapter 2, and Host-only for Adapter 3īridged duplicates NAT & Host-Only, so it can confuse the VM OS. I can connect to my guest using screen sharing from my host, and there, my username/password combination does work, and I can drop files from host to guest and run applications on the guest Both SMB and AFP are enabled on my host Mac, and I can see there that 1 user is connected by SMB (obviously, the ‘Guest’ user of my virtual Mojave). I cannot see the content of ‘Applications’, though. In my virtual machine, I see ‘Connected as: Guest’, and I see one folder there, ‘Applications’ (which I had shared), but not the other shared folder. ![]() I cannot, however, connect to my host from the guest or vice vice using my admin user name and password (I do have different user name/pw for host and guest, respectively). Bridged networking did not have any effect Host-only does allow me to see my host in my guest. I did play around with the network settings in VB, leaving NAT on for Adapter 1, and enabling both bridged for Adapter 2, and Host-only for Adapter 3, and enabling screen sharing and file sharing in my virtual machine. Thank you for your suggestions, and I am not that technically well-versed in networking, so maybe would need some more elaborate step-by-step advice. Thank you for helping me to configure my Virtual Mojave so that I can overcome the three problems mentioned. I have also tried to install a Mojave virtual machine on another Mac running Ventura (13.1) and VirtualBox 7.0.4, but there I failed to even install Mojave. My host system is Mojave 10.14.6 if that should be of any significance – I have not updated so far since I need some 32-bit apps, and want to make sure to get a VirtualMojave up and running before I upgrade my host. (3) Lastly, Shared Clipboard and Drag and Drop do not work either, even though they are set up as bidirectional in Settings. I also tried to share these folders from my host using smb, without success (my host user name/pw is not accepted, and neither is guest access). However, none of these folders shows up anywhere when I run my MojaveVirtual machine. I gave them a new name to be used in VB, granted full access, and set them to automount. In Settings/Shared Folders, I set up two of my host system’s folders as shared folders (Applications, and Downloads). Failed to connect USB device Samsung PSSD T7 to the virtual machine MojaveVirtual.ĭetails: Failed to create a proxy device for the USB device. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |